The control table is the main control for all of your GENERAL ELECTRIC washer? s capabilities. The switches, dials, and knobs almost all connect to typically the control board. If it shorts out and about or gets broken, your machine will start to reduce functionality or will certainly stop working completely. Models with a digital readout could also screen an error code telling you if the control board has stopped operating. If you such as fixing your individual appliances, this is a fix you can make yourself. Order alternative part #WH12X10468 intended for most GE cleaner models. Then follow these steps in order to uninstall and substitute the old command board.
Unplug the washing machine.
This is the first step in order to any appliance restoration project. Once you have recognized what? s inappropriate with your machine, make sure you unplug it completely so you stay safe from electrical discharge and shock.
Disassemble the washer.
Take the washer away from the wall. You only need enough area to slide the top access -panel back. If a person have room, consider to pull typically the washer away by the wall because little as probable which means you don? to must detach the particular hoses or switch off the water.
Eliminate the three screws along the back edge of typically the top access panel and the about three screws along the particular back side of the lean alongside the management panel. Then you can definitely pull the top panel an inch again, which loosens the hold on the particular front trim item. Carefully pry the trim without any the tabs and set that aside. Lift the particular top panel? t back edge upward and then set the full panel apart.
Eliminate the control panel next. To start, move out the cleaning agent drawer in typically the left-hand side plus depress the video at the back of the compartment to help you remove this entirely. Set this aside. Remove the screw next to the particular detergent drawer real estate. Next, remove typically the screws along the back of the particular control panel gaming console. Also, pry upward the top edge of the system to loosen the particular control panel. Keep onto the management panel and hit the two fastening tabs on the back again of the console inside the washing machine. Once it comes free, don? big t pull it aside or allow it to fall. Instead, tilt that down so that you can begin to unplug the wires.
You will need to disconnect all of the particular wire harnesses attached to the command panel. What you just have to do is press straight down the tab to each plug. You don? t have to be able to worry about mixing up them up during reinstallation because each and every plug has an unique shape. Even so, should you? re stressed about working with washing machine repair man , require a picture from multiple sides so you have a visual guide of exactly where each wire control should go.
As soon as the control panel is totally detached through the machine, move it in order to a work surface area. This is the part that residences the control board.
Remove the old control board.
Leave the control screen face down. Take out the screws along the perimeter from the control board. There should be four. Also, depress the locking tab along the edge from the control panel nearest the curving edge of the control panel. These can be difficult to be able to reach, so employ a flathead electric screwdriver to move the tabs. Pull the control board out and shift the particular control panel apart.
Flip the command board over. Consider a picture of all the keys in the front side of the control panel therefore you have some sort of visual guide in the course of reinstallation. Then start off removing each of the switches and assemblies therefore you can proceed them over to the new portion. They should end up being relatively loose, consequently don? t apply too much pressure on the slim plastic parts.
Mount the new control plank.
Before you put the new control board part within the control panel console, mount all of the buttons you eliminated from the old part. The more time assemblies will usually have hooks that must be slid into typically the cutouts on typically the control board in order to provide extra balance. Make sure each and every of the buttons is installed so they match the image guide.
Once the buttons are generally within place, pick upwards the control panel and tilt that so it? s almost perpendicular to typically the ground. Get in line the particular control board? t shaft together with the gap in the control panel. As you carry out so, wiggle typically the knob a bit and so the shaft lines up with the opening and snaps totally into place. The particular control panel helps hold the buttons in place, but when you tilt the particular control board as well far forward in this step, some regarding the buttons may come loose. if anything falls misplaced, just reinsert the hooks and consider again.
Once the control board base is place, meticulously keep both bits held together in addition to set the management panel face down. Now you may lock both the items together by lightly pressing the three fastening tabs into spot and retightening typically the four screws around the edge from the control board.
Reassemble the washer.
Very first, orient the handle board assembly beside the top associated with the front associated with the washer and so the curved edge is definitely closest to the machine. Start insert the wire wires into the command board by using the style guide or even by matching each wire harness to the correct plug.
Next, tilt the control panel regress to something easier so it? t flush with typically the top front regarding the washer, and ensure none of the particular wires get pinched. Slide the dividers along the underside into the slots on the right part, and snap the particular the control panel into location. After that, retighten the particular screw that rests alongside the cleaning agent drawer housing. Also, retighten the anchoring screws across the back of the the control panel. After that slide the detergent drawer into spot and reattach the particular top access panel. If you appear at the bottom part of the top entry panel, you? ll notice slots for the circular limits along the rail. The pins require through the greater end of typically the cutout so the screen lies flat and then, when a person slide the -panel forward, lock straight into place against the particular smaller part of the particular cutout. This element can be tricky, so an aesthetic guide like at the end of this video might help.
To get this done, arranged the top accessibility panel carefully together with the frame plus the pins. It should hand approximately the inch off typically the back. Before you slide the panel forward, press typically the trim into location on the three securing tabs. Then glide the panel frontward and add back all six anchoring screws to hold this set up.
Push your current washer back into place and stopper it in. Adhere to the guide of which came with the particular control board to be able to program the machine. Each model features a slightly different step. As soon as your washer has been programmed, that? s prepared to start a new cycle.